Focos Led - L135mm-5.3 2-pack 4w G23 Pl-s 7w Plug In Recess

Descripción

------
------ YMAGINARIUM
------ By MS
------
------ Tu intermediario aliado.
------ ¿Si tienes dudas?: No dudes en preguntar, antes de ofertar.
------
NOMBRE EN ESPAÑOL: Focos LED - L135mm-5.3" 2-Pack 4W G23 PL-S 7W Plug in Recessed PL Bulb E-Simpo 2-Pin Horizontal Retrofit CFL PLS-7W Replacement 85-300V 180 View Angle Ceiling Lamp (Daylight *******k)
NOMBRE EN INGLES: L135mm-5.3" 2-Pack 4W G23 PL-S 7W Plug in Recessed PL Bulb E-Simpo 2-Pin Horizontal Retrofit CFL PLS-7W Replacement 85-300V 180 View Angle Ceiling Lamp (Daylight *******k)
* 2-Pack 4W 2Pin G23 LED Bulb, Can Work with Inductance Ballast, BUT CAN NOT work with Electronic Ballast,so if the fixture has an Electronic ballast, Please DON'T plug directly, BYPASS ballast First!.
* *******lm Low heat, as we have not run all of the LED Power, make sure there is less light attenuation, and keep a longer life and sustainable light performance.
* Replace Compact Fluorescent Lamps-CFL widely used in Recessed-Surface-mounted Down lights, Recessed Cans, Table-Desk Lamps, Portables, Pendant Lamps, Ceiling Fixtures, Wall Washers, Wall Sconces, Family Rooms, Living Rooms, Kitchens, Dining Rooms, and Porches.
Specification
Input Voltage: 85-300V AC
Power: 4W
NO Dimmable
CRI>82
LED: SMD2835
Brightness: 4W *******Lumens
Color Temperature: Warm White *******K; Cold White *******K
Application:
3W is used to Replace 2-Pin CFL PL-S 5W
4W is used to replace 2-Pin CFL PL-S 7W
Note:
1. Please check if the inside ballast is inductive ballast or electronic ballast;
2. If it is inductive ballast, you can use this LED lamp directly, just plug and play.
3. If it is electronic ballast, the led driver can not work compatibly with the electronic ballast, so you have to bypass the electronic ballast. Otherwise the LED Lamp witll get flicking, burnt, smell, damaged.
How to bypass the ballast?
1. Turn Off the Power.
2. Find the Ballast. Usually it is embeded inside the ceiling fixture. Pls pull off the existing PL lamp, reflector. Leave wire in junction box. and find the ballast.
3. Normally, the Ballast has a black and white wire on the input side (AC input side, 100V -120V for North America). It also has two red and two blue output wires. To bypass this ballast, please cut all the Input and output wires, so total 6 wires cut.
4. Then, you can connect the two red wires to the black wire.
5. Next, connect the two blue wires to the white wire. now ballast is bypassed.
----------------------------------------------------------------------------------
------ POLITICAS
----------------------------------------------------------------------------------
Todos nuestros productos son traídos del exterior; por ello, los tiempos de entrega son a:
* Ciudades Principales: de 5 a 10 días hábiles
* Otras Ciudades: de 7 a 12 días hábiles
CONDICIONES DE LA VENTA:
* Somos una tienda virtual que facilita la obtención de tus productos con proveedores desde el exterior
* La obtención de los artículos a Medida (Talla o Color) deberán ser consultados a través del chat público de ML y en caso de compra: estos deben ser consultados y confirmados en el chat Post-Venta.
NUESTRA GARANTÍA: Nuestros proveedores nos ofrecen una garantía de 30 días la cual extendemos a nuestros clientes, esta cubre daños por defectos del material o errores en la fabricación. NO cubre mala manipulación por parte del usuario.
IMPORTANTE: Debe conservar el embalaje de su producto en buen estado, o en su defecto la etiqueta; así mismo, recuerde que no se aceptan devoluciones por error en la selección del producto.

Garantía del vendedor: 30 dias